Konica minolta bizhub drivers c654 Ps4#

The 1st folding stopper home sensor (PS603) is not turned ON even after the set period of time has elapsed after the 1st stopper motor (M602) starts searching home position. Description: 1st stopper motorвЂ™s drive malfunction.5 M302 operation check PKCB CN34-1 to 6 PK-521 5-C. 4 PS303 I/O check, sensor check PKCB CN37-2 (ON) PK-521 5-C. 3 Check the connector between PS303-relay CN342- relay CN341-PKCB CN34 for proper connection, and correct as necessary. 2 Check the connector of M302 for proper drive coupling, and correct as necessary. Remedy: 1 Check the connector between M302-relay CN342- relay CN341-PKCB CN37 for proper connection, and correct as necessary.The PK punch home sensor (PS303) is not turned ON even after the set period of time has elapsed while the punch oscillating motor (M302) is energized. Description: Punch oscillating motorвЂ™s drive malfunction.7 M201 operation check PIDB CN54-7 to 8 PI-505 4-C to D. 6 PS205 I/O check, sensor check PIDB CN55-7 (ON) PI-505 6-C to D. 5 PS204 I/O check, sensor check PIDB CN55-8 (ON) PI-505 5-C to D. 4 Check the connector between PS205-relay CN235- PIDB CN55 for proper connection, and correct as necessary. 3 Check the connector between PS204-relay CN235- PIDB CN55 for proper connection, and correct as necessary. 2 Check the connector of M201 for proper drive coupling, and correct as necessary. Remedy: 1 Check the connector between M201-relay CN203- PIDB CN54 for proper connection, and correct as necessary.

The tray lower limit sensor /Up (PS205) or tray upper limit sensor /Up (PS204) are not turned ON even after the set period of time has elapsed after the tray lift motor /Up (M201) is energized.

Description: Sheet feeder up/down drive failure (upper).

7 M202 operation check PIDB CN56-5 to 6 PI-505 7-C to D. 6 PS210 I/O check, sensor check PIDB CN53-11 (ON) PI-505 9-C to D. 5 PS209 I/O check, sensor check PIDB CN53-8 (ON) PI-505 8-C to D. 4 Check the connector between PS210-relay CN236- PIDB CN53 for proper connection, and correct as necessary. 3 Check the connector between PS209-relay CN237- PIDB CN53 for proper connection, and correct as necessary. 2 Check the connector of M202 for proper drive coupling, and correct as necessary.

Remedy: 1 Check the connector between M202-relay CN206- PIDB CN56 for proper connection, and correct as necessary.

The tray upper limit sensor /Lw (PS209) or tray lower limit sensor /Lw (PS210) are not turned ON even after the set period of time has elapsed after the tray lift motor /Lw (M202) is energized.

Description: Sheet feeder up/down drive failure (lower).

5 M9 operation check SDDB CN11-11 to 20 SD-512 1-B. 4 PS8 I/O check, sensor check SDDB J7-3 (ON) SD-512 5-G.

3 Check the connector between PS8-relay CN10-SDDB J7 for proper connection, and correct as necessary.

2 Check the connector of M9 for proper drive coupling, and correct as necessary. When FS-535+SD-512 is installed: 1 Check the connector between M9-SDDB J11 for proper connection, and correct as necessary. 5 M9 operation check SDDB J11-11 to 20 SD-511 1 to 2-B. 4 PS8 I/O check, sensor check SDDB J7-3 (ON) SD-511 6-G. Remedy: When FS-534+SD-511 is installed: 1 Check the connector between M9-SDDB J11 for proper connection, and correct as necessary.The center fold home sensor (PS8) is not blocked even after the set period of time has elapsed while the center fold knife motor (M9) is energized. The center fold knife home sensor (PS8) is not blocked or unblocked even after the set period of time has elapsed after the center fold knife motor (M9) is turned ON. Description: Center fold knife motorвЂ™s malfunction.5 M3 operation check SDDB J7-7 to 10 SD-512 5-F to G.

Konica minolta bizhub drivers c654 Ps4#

4 PS4 I/O check, sensor check SDDB J7-6 (ON) SD-512 5-G. 3 Check the connector between PS4-relay CN10-SDDB J7 for proper connection, and correct as necessary. 2 Check the connector of M3 for proper drive coupling, and correct as necessary. When FS-535+SD-512 is installed: 1 Check the connector between M3-relay CN10-SDDB J7 for proper connection, and correct as necessary. 5 M3 operation check SDDB J7-7 to 10 SD-511 5-F to G. 4 PS4 I/O check, sensor check SDDB J7-6 (ON) SD-511 6-F.

Remedy: When FS-534+SD-511 is installed: 1 Check the connector between M3-relay CN10-SDDB J7 for proper connection, and correct as necessary.

The alignment home sensor (PS4) is not blocked or unblocked even after the set period of time has elapsed after the alignment motor (M3) is turned ON.

Description: Alignment motorвЂ™s malfunction.